This is for 1 fence, the rails, and 8 bolts pictured. Delta 34-670 or a 36-600 round Table Saw Round Rip Fence for a 22 deep table top. Fence locks down well to table top and works as it should. Does have scratches and scrapes as this is a used fence. Fence does work well and is intended for 22 deep Delta 34-670 table top. Will also fit 36-600 with 22 deep table top.
Includes rip fence exactly as shown. The length of this rip fence is meant for a 10″ table saw with a cast iron top that measures 27″ deep (when measured from to back), not including the rails. NOTE – it will NOT fit a top that measures 22-1/4 from front to back.
Removed from a working 113.299110 Craftsman table saw. Would fit any Sears Craftsman Rip Fence System for Saws with a 27 Cast Iron Deep Table Tops (when measured from front to back, no including any existing rails)… That said it’s possible you may need to drill a few new holes for mounting. NOTE – these older style fences do not use a back rail… The fence simply rides along the front rail and clamps to the back of the top when the handle is pressed down. NOTE – the smaller fence piece is for your wing extension (if you have one). Fasteners and Spacers as shown. Visit my online shop. For even more table saw parts!
Includes rip fence only, exactly as shown. Fits rail that is 1.38 (aka 35MM) in diameter. The length of this rip fence is meant for a 10″ table saw with a cast iron top that measures 27″ deep (when measured from to back), not including the rails. NOTE – it will NOT fit a top that. Measures 22-1/4 from front to back.
Fasteners and Spacers as shown. Removed from a vintage Craftsman. Came off a working Craftsman 113.27700… It will fit other vintage (50′s or 60′s) Craftsman Rip Fence System for Saws with 22 Cast Iron Deep Table Tops (when measured from front to back). Be sure to measure BEFORE purchasing as many other vintage models have either a 20″ deep top, or a 27″ deep top. This fence will NOT work with those models. NOTE – these older style fences do not use a back rail… The fence simply rides along the front rail and clamps to the back of the top when the handle is pressed down. Visit my online shop. For even more table saw parts.
Estate find, AS FOUND, uncleaned, very nice condition; for restoration, parts or repair, rust, wear, dents, dings; please see all photos, need clean up from long storage, AS IS AS SHOWN, location Z4. Please see our other listing for collectible tools for the mach inists, mechanics, steampunk, collectible antiques, jewelers, woodworking blacksmith tools & more. We will be liquidating a large estate consisting of military items, woodworking tools, automotive tools, machinists tools, mechanics tools, collectibles, antique and primitives and more. Please put us in your favorites you will not be disappointed. I will try to describe these items to the best of my ability and would not misrepresent anything intentionally. I list the defects, problems and imperfections I see on the items, but I can sometimes miss something or make a mistake. I try to answer every question asked, but cannot guarantee an answer if you ask the day the listing ends. ALSO PLEASE DO NOT ASK US TO SHOW AS A GIFT OR MISREPRESENT THE CONTENTS OR VALUE. Track Page Views With. Auctiva’s FREE Counter.
Fasteners and Spacers as shown. See photos for details. Removed from a working Craftsman model 113.24280. Should fit just about any Sears Craftsman Rip Fence System for Saws with 20 Cast Iron Deep Table Tops (when measured from front to back). Note – this style fence does not use a back rail… The fence simply rides along the front rail and clamps against the back of the cast iron top and wings. WILL NOT FIT A FULL SIZE CRAFTSMAN, AS THOSE TYPICALLY HAVE 27 DEEP CAST IRON TOPS. Visit my online shop. For even more table saw parts!
Came off a Rockwell saw that had no model number listed. Fits a cast iron top that is 22 deep when measured from front to back (not including the rails). See the photos for details. Condition is good, just one small cut on the end of the front rail as shown in the photos. The spacing on the factor drilled mounting holes was 11-1/2 apart on that saw in the front for that saw. I don’t have any other measurements to offer but that should be a good start and you can drill new holes as needed for mounting. Visit my online shop. For even more table saw parts!
Estate find, AS FOUND, uncleaned, very nice condition; for restoration, parts or repair, rust, wear, dents, dings; please see all photos, need clean up from long storage, AS IS AS SHOWN, location Z4. Please see our other listing for collectible tools for the mach inists, mechanics, steampunk, collectible antiques, jewelers, woodworking blacksmith tools & more. We will be liquidating a large estate consisting of military items, woodworking tools, automotive tools, machinists tools, mechanics tools, collectibles, antique and primitives and more. Please put us in your favorites you will not be disappointed. I will try to describe these items to the best of my ability and would not misrepresent anything intentionally. I list the defects, problems and imperfections I see on the items, but I can sometimes miss something or make a mistake. I try to answer every question asked, but cannot guarantee an answer if you ask the day the listing ends. ALSO PLEASE DO NOT ASK US TO SHOW AS A GIFT OR MISREPRESENT THE CONTENTS OR VALUE. Track Page Views With. Auctiva’s FREE Counter.
