Get the max savings on the INCRA Miter Gauge Combo Pack. The package includes the INCRA Miter 1000SE plus the INCRA Miter Express. This combination of two great INCRA crosscutting tools is incredibly practical and convenient. When mounted to the Miter Express, the Miter1000SE can easily crosscut 24 deep panels, offers the increased control of using a sled, and allows great safety for cutting small parts using the Miter Express heavy-duty hold-down clamp and T-slots that easily accommodate shop-made jigs and fixtures. The Miter 1000SE can also be removed from the Express sled in seconds and used by itself for quick solutions to a variety of operations, such as working at a router table or cutting bevels with the saw blade tilted. Dock & Lock the included INCRA Miter Gauge in Seconds. Removable t-slot retaining clips & adjustable miter bar. GlideLOCK Miter Bar – The Miter 1000SE’s 6 expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard miter gauge channels. Special Edition Telescoping INCRA-LOCK Fence. Special Edition 1/10th° Vernier Cursor. Table size: For adequate support, the Miter Express requires a minimum of 11 from the side of the blade to either the left or right edges of the saw (sled can be installed on either side of the blade).
Excellent Aluminum Alloy Material: This table saw miter gauge fence is made of excellent aluminum alloy material, which is sturdy and wear resistant, not easy to be damaged, and has a long service life. High Accuracy: This table saw miter gauge fence features high accuracy, and the minimum adjustment accuracy is 0.002mm. Double Sided Scale: This table saw miter gauge fence features a double sided scale, with one metric side and one imperial side, which can be switched freely. Easy To Operate: This table saw fence is very easy to operate, you can align the scale as you need and cut without measuring and scribing. Wide Application: This table saw miter gauge fence is widely used for woodworking, modeling, DIY and furniture processing. Item Type: Table Saw Miter Gauge Fence Material: Aluminum Alloy Length Range: Approx. 0-850mm/0-33.46in Angle Range: 0-70 Degree. 1 x Table Saw Miter Gauge Fence. 2 x Hex Socket Screw. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders.
The Perfect entrance into the Magswitch Workholding System. The Starter Kit comes complete with the Reversible Featherboard Attachment, the Universal Mounting Base and two MagJig 150′s. Once you have this tool, get all the other great tool attachments and simply mount to the base as needed. Features core advantages of Magswitch including fast, strong set up anywhere on a steel table or cast Iron fence. Not limited by the miter slot. Featherboard is reversible for left and right hand feeds. Accommodates the Vertical Featherboard Attachment for an added dimension of safety and protection against kickbacks. Low profile design for use on your smallest tables. My E-Bay philosophy is simple, you are the customer and you de. Cide how you want to handle the deal. I will go along with most anything as long as it is not too outrageous and you keep me informed. I do not have any hard and fast time lines on what happens when. If for some reason that will be delayed, I will let you know. You decide how you want to pay and I will usually go along with it. So far all (well, most) of my dealings have been with nice, honest people. (As I would expect). My satisfaction policy is also very simple, you are the customer and you decide if you want the item. Satisfaction is guaranteed, no exceptions. The free listing tool. California Residents: This tool may contain a component part or create wood dust which contains a toxin on California’s Prop 65 chemical list. WARNING: Cancer and Reproductive Harm.
MicroLux® Miniature Table Saw. Ideal for Ultra-Miniature Sizes. Saw includes sturdy 6-1/4″ x 6-1/4″ stationary aluminum table, Overall size: 9-1/2″wide x 7-1/4″ deep x 4 high. The NEW MicroLux Miniature Table Saw is Ideal for Ultra-Miniature Sizes. Adjustable, angled vacuum port attachment. Wide-body, self-aligning rip fence with undercut clamp for more secure positioning. The NEW MicroLux Miniature Table Saw is Ideal for Ultra-Miniature Sizes Designed specifically for rip-cutting narrow strips from sheet stock and for cross-cutting to close tolerances, the MicroLux Mini Table Saw will even cut plastic, thin non-ferrous metals and printed circuit board with our optional fine-tooth blades. NEW features include: Pivoting action clear blade guard for better visibility Tool-less dust compartment door latch Adjustable, angled vacuum port attachment Built-in sliding scale on the table top for precise cuts Wide-body, self-aligning rip fence with undercut clamp for more secure positioning MicroLux Miniature Table Saw includes sturdy 6-1/4″ x 6-1/4″ stationary aluminum table, adjustable rip fence, 0 to 90 degree miter gauge, blade guard, dust catcher compartment benchtop mounting holes, up-front on/off switch, standard blade #50320, 2 dia. With 10 mm hole and 80 teeth, 3600 rpm, 1/10 hp, 110VAC motor with belt drive and 6′ cord. Overall size: 9-1/2″wide x 7-1/4″ deep x 4 high. High-quality, made in Japan. Any product you return must be in the same condition you received it and in the original packaging. We usually respond within 24 hours on weekdays. Thank you for shopping at our store.
Premium Precision Miter Gauge with Aluminum Fence: Versatile Cut Solutions. High quality and economical solution for table saw cross cutting needs. Aluminum Miter fence with 45 degree ends for unsurpassed workpiece support. Includes aluminum flip stop for repetitive angled cuts. Alternative Carriers – We may use alternative carriers e. To ensure your package arrives safely and on time. Your feedback is extremely important to us. We strive to provide the best products and customer service possible. We are committed to resolving any problems and ensuring your satisfaction. Thank you for supporting our small family business!
The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs. The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs. 200 thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The head is mounted to a solid steel miter bar that measure 18 in length and is. Standard miter slots are 3/4″ x 3/8″ with a 1/8″ “T slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8″ in diameter and is just shy of 1/8″ to fit into to the “T” slot to prevent accidental lifting when feeding your stock through. Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary. Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading. Fulton Precision Miter Gauge with Aluminum Miter Fence and Flip Stop. We’ve all done the research or at the very least heard about miter gauges with fence systems that are very accurate, easy to adjust and make cross cutting angles on your table saw super easy. While that all sounds great, all those great features usually costs a lot. That is until now! The Fulton Precision Miter Gauge with Aluminum Miter Fence and Flip Stop comes packed with all those great features and more. The best part is that it is reasonably priced so that most any woodworker can afford it! Be Precise with Ease. If you have ever used a factory supplied miter gauge, then you know how limiting it can be. The Fulton Miter Gauge with Aluminum Fence and Stop makes the angle cutting process a breeze. Once the gauge is set and the fence is properly adjusted, cross cutting angles on your table saw just became a whole lot easier than just using a miter gauge by itself. When this aluminum fence is used with the Fulton Miter Gauge, you’ll be able to repetitively cut angle stock all day long with precise results! When designing the fence for this system we kept having the same issue happen over and over again. The standard 90 degree end on most miter gauge fences made the fence to saw blade gap too large and the wood kept binding in that gap. Our solution was to simply cut the fence ends at a 45 degree angle so that the fence can get as close as possible to the blade with minimal stock over hang. This helps prevent binding and produces a much cleaner cut. Convenient Aluminum Flip Stop. Included with the fence and miter gauge is a convenient flip stop for making repetitive cuts. Simply slide the flip stop to the exact position you need it to be, lock it in place and you’re ready to go! When the stop is not needed you can either remove from the fence or simply lift the stop upwards and out of the way until it is needed. Accurate and Easy to Adjust. The Fulton Miter Gauge is loaded with great features. One of the more prominent features are the positive stops that are set to the most common angles used by woodworkers. Simply loosen the handle by rotating it counter clockwise, pull the spring loaded pin lock up and and adjust the miter gauge to the desired angle. Once you find your positive stop angle, release the lock pin so it locks the angle in place and re-secure the handle by rotating int clockwise until it is snug. If you want to use an angle that is not one of the positive stops, the pin lock can be pulled upward and rotated so that it won’t engage any of the positive stop holes. This allows you to adjust the miter gauge to any angle you need. Left Side, Right Side or Even Upside Down.. For the most part, we tend to cut on one side of our table saw the majority of the time. It usually depends on the saw or just simply preference. This is why we included two different sticky back (PSA pressure sensitive adhesive) tapes so you can choose which direction you need. We also know that some of use like to do things a little differently. If you are looking down at your miter fence from above then it may make sense for some of us to place the tape on to the aluminum fence upside down in relation to the miter gauge. This allows for you to be able to clearly read the measurements on the tape. Standard Size Miter Bar 3/4″ x 3/8″. The steel miter bar is mounted to the miter gauge and is the industry standard of 3/4″ x 3/8″. This means it will fit into most table slot miter slots. The miter bar also features spring loaded plungers that can be adjusted (with a hex key wrench) for just the right fit so you have a smooth push through every time.
MICROJIG GRR-RIPPER GR-200 Advanced Adjustable Table Saw Pushblock, Yellow. GR-200 Features Include: 3-Directional Force for total control of the workpiece and virtually eliminate kickback. Cutting Range (Table Saws):1/4 to 5 inch. Precise 1/4 thin rips. Stabilizes for cutting bevel rips, resawing, irregular-shaped stock, dowels, dados and more. Designed in the USA. A true MICROJIG Innovation. GRR-Ripper Advanced 3D Push block is the ultimate in safety, precision, and control. A must-have for any table saw user. Essential for protection against injury, virtually eliminating kickback, and controlling your work piece large and small accurately. Guide and rip along the rip fence using the powerful gripping non-slip surface to control the stock through the cutters. Rips down to 1/4 standard without readjusting the fence. The Adjustable Center Leg accommodates for a variety of sizes and widths. Built-in Balance Support Stabilizes for narrow and small work pieces on the table saw and router table for safer, straighter, and cleaner cuts. The Handle is adjustable for ergonomic comfort. Includes 2 additional accessories: the Adjustable Spacer and the Stabilizing Plate. The Adjustable Spacer – This accessory adds increased gripping surface for tackling larger stock. It also adds one inch of cutting width to the GRR-Ripper. Also, acts as a secondary balance support for small stock and straight-line ripping. Great add-on for working on the Router Table, and eliminating snipe. The Stabilizing Plate – The Stabilizing Plate adds a new dimension of control to the GRR-Ripper. It is particularly useful when cutting small narrow pieces of stock. Perfect for trickier cuts like resewing, bevel edging, pattern routing, and much more. The Stabilizing Plate also performs as the secondary fence that travels with the GRR-Ripper along the left side of the stock. It holds the off-cut piece in its original position through the entire cutting operation. Without binding the operation, it provides enhanced stability over the cut and superior guidance along the fence. Made in the USA. Watch the Action Video and Add to Your Cart Today. Cut ultra thin rips, stabilize for odd shaped material, built to last. 9″L x 3″W x 7H. We are not responsible for undeliverable addresses. Your feedback very important to us, after you get your package and you are. Satisfied with our service. If you have any problem with your order / any questions please before leave any type of feedback. Thank you for shopping at our store.
[GREAT AT CROSS & RIP CUTS] The steel rip fence and riving knife system lets you perform an assortment of straighter, longer, wider cuts. [TRULY PORTABLE TABLE SAW] Weighing in at less than 15 lbs. You easily can move it around your workshop or even take it to the job site. [ADJUSTABLE MITER GAUGE] Makes 0-60? Miter cuts from both the right and left sides, so you can make every common miter cut, and every angle in-between. [SAFETY SWITCH] An added safety switch and safety key give this saw an added level of security, so you don’t have to worry about accidental starts. DO IT WITH WORX. WORX tools are engineered with cutting-edge technology, and above modern efficiency standards, so you can build a cost-effective tool collection that’s been designed to last. On-board storage for miter gauge, rip fence and blades. [ACCESSORIES INCLUDED] 5 blades (woods, aluminum, scrolling, ceramic tile, steel) rip fence, miter gauge, dust extraction port, and blade grip. Sets up in seconds to cut wood, metal, tile, aluminum or plastic.
